Maintenance and cleaning instructions for your Samsung Jet Bot Combo

Last Update date : 2024-11-24

The individual parts of your Samsung Jet Bot Combo and Clean Station should be regularly maintained to ensure proper functionality. You can follow the steps in our guide to clean the various parts, such as the dust filter, sensors, and brush.

Close-up of the underside of a Samsung Jet Bot Combo, displaying its dual spinning, gray microfiber cleaning brushes.

Follow the instructions below when cleaning the fine dust filter.

1 Detach the Fine dust filter cover at the rear of the Clean Station by grasping the grooves and pulling it out.
Diagram illustrating the removal of the fine dust filter cover from a Samsung Clean Station, highlighted by a blue arrow.
2 Detach the Fine dust filter. Shake out and empty the filter.
Diagram showing the removal and cleaning of the fine dust filter from a Samsung Clean Station, with an inset depicting shaking out debris.
3 Reattach the Fine dust filter and Fine dust filter cover. You will hear a click when they are reattached to the Clean Station.
Diagram depicting the reinsertion of the fine dust filter and cover into a Samsung Clean Station, indicated by a blue arrow.

Follow the instructions below when cleaning the Washing Plate.

1 Detach the Washing Plate from the Clean Station by lifting the handle that says “PULL”.
Diagram showing the removal of the washing plate from a Samsung Clean Station, with an inset close-up highlighting the 'PULL' handle.
2 Clean the cover with water and let it dry completely in a shaded area.
Diagram illustrating the washing of a washing plate under a tap, with water flowing onto the surface, suggesting rinsing before drying.

Note: Do not use detergent when cleaning the cover.

3 Reinsert the Washing Plate into the Clean Station.
Diagram showing the reinsertion of the washing plate into a Samsung Clean Station.

Follow the instructions below when cleaning the bottom cover of the Clean Station.

Notes:

  • Make sure the Clean Water Tank and Waste Water Tank are disassembled before placing the Clean Station on its side.
  • Detach the Extra Plate and the Washing Plate.
1 Place the Clean Station on its side and turn the 7 fixed screws on the bottom cover in the unlock direction.
Diagram illustrating the unlocking of screws on the bottom cover of a Samsung Clean Station, with circles highlighting seven screws being turned in the unlock direction.
2 Detach the bottom cover and remove any foreign materials.
Diagram showing a brush cleaning the interior of a detached bottom cover of a Samsung Clean Station, with debris being brushed away.
3 Clean the cover with water and let it dry completely in a shaded area.
Diagram showing the bottom cover of a Samsung Clean Station being rinsed under a tap and then placed to dry in a shaded area.
4 Reattach the bottom cover to the Clean Station.
Diagram illustrating the reattachment of the bottom cover to a Samsung Clean Station, indicated by a blue arrow.
5 Turn the 7 fixed screws in the lock direction.
Diagram showing the tightening of seven screws on the bottom cover of a Samsung Clean Station, with circles indicating each screw being turned in the lock direction.
6 Stand the Clean Station in its original upright position.

Follow the instructions below to learn how to empty the Waste Water Tank.

Notes:

  • Make sure the power cord is unplugged before cleaning.
  • Do not use detergent on the Waste Water Tank.
1 Detach the Waste Water Tank from the Clean Station by pulling up on its handle.
Diagram showing the removal of the waste water tank from a Samsung Clean Station by lifting its handle, indicated by an upward blue arrow.
2 Open the lid and empty out the Waste Water Tank.
Diagram illustrating the emptying of the waste water tank, showing the lid open and water pouring out.
3 Close the lid and make sure the lid’s hook is attached. You will hear a click when the lid and hook are attached.
Diagram showing the closure of the waste water tank lid on a Samsung Clean Station, with a downward blue arrow indicating the lid closing and a curved arrow highlighting the hook attachment.
4 Reinsert the Waste Water Tank into the Clean Station.
Diagram showing the reinsertion of the waste water tank into a Samsung Clean Station, indicated by a downward blue arrow.

Follow the instructions below to learn how to replace the Dust Bag.

1 Detach the Clean Station lid by pulling up on its handle.
Diagram showing the removal of the Clean Station lid by lifting its handle, indicated by an upward blue arrow.
2 Hold the Dust Bag guide handle and push it.
Diagram showing the dust bag guide being pushed by a handle inside the Clean Station, indicated by a downward blue arrow.
3 Detach the Dust Bag by pulling it up. Discard the used Dust Bag.
Diagram showing the removal of the dust bag from a Samsung Clean Station by pulling it upwards, indicated by an upward blue arrow.
4 Insert a new Dust Bag by fitting it into the grooves on the holder.
Diagram showing the insertion of a new dust bag into a Samsung Clean Station, guided into grooves on the holder, indicated by a downward blue arrow.
5 Push the top of the Dust Bag guide holder until you hear a click.
Diagram showing the top of the dust bag guide holder being pushed down until it clicks into place, ensuring the dust bag is securely fitted inside a Samsung Clean Station.
6 Close the lid.
Diagram showing the lid of the Samsung Clean Station being closed, indicated by a downward blue arrow.

The following instructions will help you descale and rinse the steamer.

Notes:

  • Do not use anything other than citric acid and water when descaling.
  • Do not use citric acid to clean any other part of the Jet Bot Combo or Clean Station.
  • Descaling should be completed once per year.
  • Descaling cannot be paused. The Jet Bot Combo cannot be used until descaling is complete.

Descaling

1 Simultaneously press and hold the Start/Stop and Charging buttons on the top of the Jet Bot Combo for 7 seconds.
Diagram illustrating the simultaneous pressing of the Start/Stop and Charging buttons on a Samsung Jet Bot Combo, indicated by speech bubble icons above the robot.
2 Dilute 100 grams of citric acid into 1 liter of water in the Clean Water Tank, and insert it into the Clean Station.
Diagram showing citric acid being diluted with water into the Clean Water Tank of a Samsung Clean Station, indicated by water pouring from a jug.
3 Simultaneously press and hold the Start/Stop and Charging buttons on the top of the Jet Bot Combo for 7 seconds.
Diagram illustrating the simultaneous pressing of the Start/Stop and Charging buttons on a Samsung Jet Bot Combo, indicated by speech bubble icons above the robot.
4 Allow the descaling process to complete. It may take about 2 hours.

Rinsing

1 Pour water into the Clean Water Tank.
Diagram showing water being poured into the Clean Water Tank of a Samsung Clean Station, indicated by a flow of water from a jug.
2 Simultaneously press and hold the Start/Stop and Charging buttons on the top of the Jet Bot Combo for 7 seconds.
Diagram illustrating the simultaneous pressing of the Start/Stop and Charging buttons on a Samsung Jet Bot Combo, indicated by speech bubble icons above the robot.
3 Allow the rinsing process to complete. It may take about 15 minutes.
Diagram highlighting various sensors on a Samsung Jet Bot Combo, including the LiDAR sensor, 3D sensor, Obstacle Detect sensor, Carpet Detect Sensor, and Cliff Sensor, all circled to indicate their cleaning points.

If the sensors (including the LiDAR sensor, 3D sensor, Obstacle Detect sensor, Carpet Detect Sensor, and Cliff Sensor) are covered in dust or other debris, the Jet Bot Combo may not function properly. You can regularly wipe the sensors using a soft cloth to remove dust and debris.

You can empty and clean the Dustbin using the instructions below.

1 Detach the upper cover of the Jet Bot Combo by lifting from the center of the cover.
Diagram showing the upper cover of a Samsung Jet Bot Combo being lifted off from the center, indicated by an upward blue arrow.
2 Hold the Dustbin handle and lift it up.
Diagram showing the removal of the dustbin from a Samsung Jet Bot Combo by lifting its handle, indicated by an upward blue arrow.
3 Open the Dustbin cover by pulling and lifting the hook on the side of the Dustbin.
Diagram showing the dustbin cover of a Samsung Jet Bot Combo being opened by pulling and lifting the hook on the side, indicated by a curved blue arrow.
4 Detach the Pre-motor filter from the Dustbin cover.
Diagram showing the pre-motor filter being detached from the dustbin cover of a Samsung Jet Bot Combo, highlighted by a blue circle and an upward arrow.
5 Remove the dust from the Pre-motor filter and the Dustbin. You can clean both parts using water. Allow them to dry completely in a shaded area.
Diagram showing the pre-motor filter and dustbin being washed under a tap, with both components laid out separately to dry in a shaded area.
6 Reattach the Pre-motor filter to the Dustbin’s lid, and then close the cover. You will hear a click when the lid is closed.
Diagram showing the pre-motor filter being reattached to the dustbin's lid of a Samsung Jet Bot Combo.
7 Reinsert the Dustbin into the Jet Bot Combo.
Diagram showing the dustbin being reinserted into the Samsung Jet Bot Combo, indicated by a downward blue arrow.
8 Reattach and close the upper cover.
Diagram showing the upper cover of the Samsung Jet Bot Combo being closed, indicated by a curved blue arrow.

Follow the instructions below when cleaning the brush and brush cover.

1 Turn the Jet Bot Combo upside down and place it on a soft cloth.
2 Push the Brush Cover Lock to the right to unlock it.
Diagram showing the process of unlocking the brush cover on the underside of a Samsung Jet Bot Combo by sliding the Brush Cover Lock to the right, indicated by a directional arrow.
3 Detach the brush cover and use the provided cleaning tool to clean it.
Diagram showing the removal of the brush cover from a Samsung Jet Bot Combo with a curved arrow indicating lifting motion, and a cleaning tool being used to clear debris from the brush.
4 Detach the brush and use the provided cleaning tool to clean it.
Diagram showing the brush being detached from a Samsung Jet Bot Combo, indicated by an upward arrow, and a cleaning tool being used to remove debris from the brush.
5 Reattach the brush by placing it into the groove and then pushing it down.
Diagram showing the brush being reinserted into the groove of a Samsung Jet Bot Combo, indicated by a downward blue arrow and an inset highlighting the correct alignment.
6 Reassemble the brush cover by aligning the 3 hooks with the grooves. Then, push the Brush Cover Lock to lock it in place.
Diagram showing the brush cover being reattached to a Samsung Jet Bot Combo by aligning the three hooks with their grooves, followed by locking the brush cover in place using the Brush Cover Lock.

Follow the instructions below when cleaning the Roller.

1 Turn the Jet Bot Combo upside down and place it on a soft cloth.
Diagram showing a Samsung Jet Bot Combo turned upside down and placed on a soft cloth, ready for cleaning.
2 Use a flat-head screwdriver to lift the Roller’s hook.
Diagram showing the use of a flat-head screwdriver to lift the roller's hook on a Samsung Jet Bot Combo, indicated by a curved blue arrow.
3 Detach the Roller by lifting it up.
Diagram showing the roller being lifted up and detached from a Samsung Jet Bot Combo, indicated by an upward blue arrow.
4 Use the provided cleaning tool to clean the Roller.
Diagram showing the provided cleaning tool being used to remove debris from the roller of a Samsung Jet Bot Combo.
5 Reinsert the Roller, and then attach the hook. You will hear a click when the hook is properly attached.
Diagram showing the roller being reinserted into the Samsung Jet Bot Combo, with the hook being attached to secure it, indicated by downward and curved blue arrows.

Follow the instructions below when cleaning the driving wheel and mops.

1 Turn the Jet Bot Combo upside down and place it on a soft cloth.
Diagram showing a Samsung Jet Bot Combo turned upside down and placed on a soft cloth.
2 Use the provided cleaning tool to clean the Driving Wheels.
Illustration of a hand using the provided cleaning tool to clean the Driving Wheels of the Samsung Jet Bot Combo.
3 Next, detach the Mops and the Mop Spin boards.
Diagram showing the detachment of the Mops and Mop Spin boards from the bottom of the Samsung Jet Bot Combo.
4 Rinse the Mops and Mop Spin boards with water.
Diagram showing the Mops being rinsed with water and the Mop Spin boards being cleaned with the provided cleaning tool.
5 Reattach the Mop Spin boards.
Diagram showing the Mop Spin boards being reattached to the bottom of the Samsung Jet Bot Combo.
6 Reattach the Mops by aligning them with the groove in the center of the Mop Spin boards.
Diagram showing the proper alignment of the Mops with the groove in the center of the Mop Spin boards on the Samsung Jet Bot Combo. A checkmark indicates correct placement, while a cross marks incorrect alignment.

Follow the instructions below when cleaning the Spin Brush.

1 Clean the Spin Brush using a steamed towel. You can wrap the Spin Brush in the towel for about 10 seconds.
Diagram showing a person cleaning the Spin Brush of a Samsung Jet Bot Combo using a steamed towel, wrapping the towel around the brush for effective cleaning.
2 If hair, threads, or other debris are tangled in the Spin Brush, use a screwdriver to detach the Spin Brush and remove the debris.
Diagram showing a person using a screwdriver to detach the Spin Brush from a Samsung Jet Bot Combo, preparing to remove tangled hair, threads, and debris.

Note: For any further questions, Contact us.

Related Questions

Thank you for your feedback!

Contact Us

Online

There are a number of a different ways of contacting us via Live Chat, Email and more
Learn more

Call

Speak to one of our dedicated team of experts
Learn more

Face to face Support

Search the nearest Samsung Service Centers in your area.
Find a service center

Apps & Services Customer Support

Samsung Health Monitor : 800-7267864
Samsung Pay : 800-7-729 (S-PAY)
Samsung Rewards : 800-7267864
View more