How to self-repair the Galaxy Z Fold5

First, have all the genuine parts and tools needed for the procedure ready

_{*Use only demagnetised tools that are specifically designed for small electronic repairs, as most electronic parts are sensitive to electromagnetic forces.}

_{*For any model-specific instructions, please refer to the appropriate repair guides.}

Samsung genuine parts - Galaxy Z Fold5

Screw 3404

Screw 3442

Screw 3513

Back Cover Adhesive tape

3rd Mic Hole Adhesive tape

Vibrator Adhesive tape 

Screw 3513

Cover Screen inner Adhesive tape (Right)

Cover Screen inner Adhesive tape (Left)

Cover Screen outside Adhesive tape 

_{*Always use Samsung-authorised genuine parts. Third-party replacement parts may not function properly.}

Repair tools

• Heating bag
• Opening tool
• Screwdriver PH0
• ESD-safe tweezers
• SIM ejection pin 
• Opening pick (Metal)
• Suction cup
• Opening picks

 

_{*You could use existing demagnetised tools that you own to perform repairs.}

_{*ESD: Electrostatic Discharge.}

When repairing devices, you absolutely must wear equipment for your safety

Safety equipment

• Safety glasses
• ESD-safe gloves
• Mask

 

_{*ESD: Electrostatic Discharge.}

Perform the repair in a ventilated area and watch out for burns and other injuries

Have your data backed up safely and ensure the device is turned off

Before beginning any repair, make sure your battery is fully discharged

Starting off, make sure to remove the SIM tray using SIM ejection pin

_{*Disassembling with the SIM tray still inserted may damage the device.}

We’re all set! Shall we start disassembling?

Back Cover

Place the Heating bag in the microwave and heat it properly following Heating bag's instruction

_{*Do not let the temperature of the Heating bag exceed 65˚C. It is recommended that you use a thermometer to properly measure and limit the temperature.}

_{*Make sure the microwave turntable spins freely so that Heating bag does not get stuck.}

_{*When handling a heated Heating bag, always wear safety gloves and be careful of burns.}

Never place a phone or tablet device directly into the microwave to heat it

To disassemble Back cover, follow 3 steps on all 4 edges of the back of the device

_{*Sequence shortened. Actual steps may vary.}

    Step. 1 Apply Heating bag on the left edge of Back Cover

    Step. 2 Attach Suction cup to the heated edge

_{*Recommended safety equipment: safety glasses, ESD-safe gloves, mask.}

    Step. 3 Use Opening pick to create a gap between Back Cover and Screen module

^{*In order not to damage the product when removing back cover, insert only the tip of Opening pick and never insert it all the way in.}

^{*When dealing with broken glass, fully equip yourself with protective gear including safety glasses, ESD-safe gloves, and mask to prevent injuries.}

Repeat the 3 steps for the top, right, and bottom edges respectively

Gently lift to remove Back cover using Suction cup

Remove Back Cover adhesive tape and 3rd Mic hole adhesive tape using ESD-safe tweezers 

Back Cover adhesive tape

_{*When assembling, use a new adhesive tape.}

Wireless charging module

Check the 2 points where the connectors are connected

_{*The locations of ports and connectors vary by device.}

Disconnect the Wireless charging module connector with the Opening pick

Using the tweezers or Opening pick, separate the adhesive tapes of wireless charging module

and separate the wireless charging module from the device

Be careful not to tear any connected components near the wireless charging module

Check the 7 points where the Screws are located

_{*The locations of ports and connectors vary by device.}

Remove all Screws on the upper rear cover using a Screwdriver

_{*Use only high-quality screwdrivers when servicing products. Low-quality screwdrivers can easily damage the heads of screws.}

_{*When assembling, use new screws.}

Disconnect the 2 flexible cable connectors with the Opening pick

Using the tweezers, lift up on the top centre

and separate the upper rear cover from the device

Disconnect the battery connector with the Opening pick

Charging port

Check the 3 points where the screws are located

Remove all Screws using a Screwdriver

_{*Use only high-quality screwdrivers when servicing products. Low-quality screwdrivers can easily damage the heads of screws.}

_{*When assembling, use new screws.}

and separate the lower rear cover from the device

Check the 2 points where the Screws are located

Remove all Screws using a Screwdriver

_{*Use only high-quality screwdrivers when servicing products. Low-quality screwdrivers can easily damage the heads of screws.}

_{*When assembling, use new screws.}

Check the 2 points where the connectors are connected

Disconnect 2 connectors from the Charging port using Opening pick

_{*The locations of ports and connectors vary by device.}

and lift Charging port away from assembly using ESD-safe tweezers

_{*Always use Samsung-authorised genuine parts. Third-party replacement parts may not function properly.}

Front camera

Check where the Front camera connector is connected

Disconnect a connector from the front camera using Opening pick

_{*The locations of ports and connectors vary by device.}

and lift front camera away from assembly using ESD-safe tweezers

_{*Always use Samsung-authorised genuine parts. Third-party replacement parts may not function properly.}

Main board

Check the 8 points where the connectors are connected

Disconnect 8 connectors from the Main board using Opening pick and separate a cable

_{*The locations of ports and connectors vary by device.}

Check the 3 points where the Screws are located

Remove all Screws using a Screwdriver

_{*Use only high-quality screwdrivers when servicing products. Low-quality screwdrivers can easily damage the heads of screws.}

_{*When assembling, use new screws.}

Using the tweezers, lift up on the separator groove to the upper left corner of the Main board and remove the Main board module

^{*Please note: You may find an alternate entry point to remove the main PBA on the opposite side shown.}

Vibrator

Using the tweezers, lift up on the separator groove to the right of the vibrator motor, and then carefully remove it from the device

^{*Please note: You may find an alternate entry point to remove the vibra motor on the opposite side shown.}

Fingerprint Scanner (Side button) 

Check 2 Screws on the Fingerprint Scanner and remove it using a Screwdriver

Using tweezers, remove the metal plate from Main Screen module

Remove the plastic bracket from the Main Screen module

The Fingerprint Scanner (Side button) is removed together with the bracket

Cover Screen

Place the Heating bag in the microwave and heat it properly following Heating bag's instruction

_{*Do not let the temperature of the Heating bag exceed 65˚C. It is recommended that you use a thermometer to properly measure and limit the temperature.}

_{*Make sure the microwave turntable spins freely so that the Heating bag does not get stuck.}

_{*When handling a heated Heating bag, always wear safety gloves and be careful of burns.}

Never place a phone or tablet device directly into the microwave to heat it

To disassemble Cover Screen, follow steps on all 4 edges of the Cover Screen of the device

_{*Sequence shortened. Actual steps may vary.}

    Step. 1 Apply Heating bag on the left edge of Cover Screen for 3 minutes

    Step. 2 Attach Suction cup and use the Metal opening pick to create a first gap

_{*Recommended safety equipment: safety glasses, ESD-safe gloves, mask.} 

^{*In order not to damage the product when removing back cover, insert only the tip of Opening pick and never insert it all the way in.}

^{*When dealing with broken glass, fully equip yourself with protective gear including safety glasses, ESD-safe gloves, and mask to prevent injuries.}

    Step. 3 Once the first partial gap has been created, the rest of the gap will be created with the plastic Opening pick 

Never use a metal pick to remove anything other than the initial gap, as you may damage the part

For the remaining three parts (left / right / bottom), use the gap at the top to create a gap with the plastic Opening pick

As the Cover Screen can be damaged by excessive force, be careful not to damage the Cover Screen

Gently lift to remove the Cover Screen using Suction cup

Before removing the Cover Screen, disassemble the Cover Screen's cable connector cover with the tweezers first

Disassemble the cable connector of Cover Screen and separate the Cover Screen completely

Remove all resin residues attached on the inside of the Cover Screen

_{*When assembling, use a new adhesive tape.}

Remove all remaining adhesive tapes attached on the device

Speakers

Check the 7 points where the Screws are located

_{*The locations of ports and connectors vary by device.}

Remove all Screws using Screwdriver

Using tweezers, lift up the top of top speaker module carefully and separate it from the device

^{*Please note: You may find an alternate entry point on the side.}

Using the Opening pick, disconnect the battery connector from the Sub-board

_{*Be careful not to damage the Battery.}

Check the 4 points where the Screws are located

_{*The locations of ports and connectors vary by device.}

Remove all Screws using Screwdriver

Using the tweezers, lift up on the separator groove to the right corner of the bottom speaker module and remove it

Sub-board

Check the 6 points where the connectors are connected

Disconnect 6 connectors from the Sub-board using Opening pick and separate a cable

_{*The locations of ports and connectors vary by device.}

Using the tweezers, lift up on the separator groove to the lower right of the Sub-board and remove the Sub-board module

_{*The Sub-board can only be replaced at a Samsung authorised repair store. Please contact Samsung for additional support.}

Button (Volume key)

Lightly press one end of the button with your fingers so that the other end protrudes

_{*When holding the buttons with a round-tip metal tweezer, be very careful not to damage or scratch the device.}

Push the tip of the protruding button up carefully with a round-tip metal tweezer and lift it up until you can grab it with your fingers

_{*When holding the buttons with a round-tip metal tweezer, be very careful not to damage or scratch the device.}

Grab the volume button with your fingers and pull it out carefully from the device

_{*Side button is also used for Fingerprint recognition sensor. Thus, it cannot be removed directly from outside.}

Samsung genuine parts - Galaxy Z Fold5

Screw 3404

Screw 3442

Screw 3513

Back Cover Adhesive tape

3rd Mic Hole Adhesive tape

Vibrator Adhesive tape 

Screw 3513

Cover Screen inner Adhesive tape (Right)

Cover Screen inner Adhesive tape (Left)

Cover Screen outside Adhesive tape 

_{*Always use Samsung-authorised genuine parts. Third-party replacement parts may not function properly.}

Before proceeding, ensure that no debris or separated Screw remains inside the device

_{*Pause the video while completing each step, then resume when ready to continue.}

Fingerprint Scanner (Side button)

Remove the release film of new plastic bracket, grab the Fingerprint Scanner (Side button) and insert it on the slot carefully

Assemble to the Main Screen module

Using tweezers, align the adhesive tape precisely at the top of the plastic bracket and attach it

and with fingers, gently press down and remove the blue release film of the tape

Using tweezers, assemble the metal plate on the Main Screen module

Check the Screws at the 2 different points of metal plate and fasten them using a Screwdriver

Screws

Sub-board

Assemble the Sub-board

Check the 6 points where the connectors are located

Connect all the cable connectors on the Sub-board

Speakers

Assemble the bottom speaker module

Check the 4 points where the Screws are located and fasten them

_{*The locations of ports and connectors vary by device.}

Screw 3513 (4ea)

Connect the battery connector to the Sub-board

Assemble the top speaker module

Check the 7 points where the Screws are located and fasten them

_{*The locations of ports and connectors vary by device.}

Screw 3513 (7ea)

Cover Screen

Attach new Cover Screen adhesive tapes

Cover Screen inner Adhesive tape (Left) 

Cover Screen inner Adhesive tape (Right)

Cover Screen outside Adhesive tape 

Remove all release film by grabbing the blue film handle

Before proceeding, ensure that no debris or separated Screw remains inside the device

_{*Pause the video while completing each step, then resume when ready to continue.}

Assemble the Cover Screen's cable connector first

Assemble the Cover Screen's cable connector cover with fingers

Attach the Cover Screen and press down the edges of the Cover Screen evenly in order to attach it perfectly

Main board

Assemble the Main board

Check the Screw’s location and fasten it

Screw 3442 (1ea) 

Screw 3404 (2ea, Black) 

Check the Screw’s location and fasten it

Connect all the cable connectors on the Main board

Assemble the Front camera and connect the connector of Front camera

Vibrator

Remove the existing adhesive tape from the bottom of the Vibrator

Attach the Vibrator Adhesive tape to the bottom of the Vibrator and peel the release film

Assemble the Vibrator and press down in order to attach it perfectly

Charging port

Insert the Charging port module to the bottom metal frame of device

Connect the 2 connectors to Charging port

Check the Screw’s location and fasten it

Screw 3442 (2ea) 

Check the Screw’s location and fasten it

Assemble the lower rear cover and press down on it in its position

Check the Screw’s location and fasten it

Screw 3442 (3ea)

Check the Screw’s location and fasten it

Wireless charging module

Connect the main battery connector to the Main board

Assemble the top of upper rear cover and press down on it in its position

Check the position of the two connectors and connect them to the Main board

_{*The locations of ports and connectors vary by device.}

Check the screw’s location and fasten it

Screw 3442 (7ea)

Check the screw’s location and fasten it

Attach the Wireless charging module adhesive tape parts and press it lightly with your finger 

and carefully attach the other adhesive tape parts of the Wireless charging module one by one

_{*When attaching the wireless charging module, make sure that it fits to the device’s form.}

Check the position of the Wireless charging module connector and connect it to the Main board

_{*When attaching the wireless charging module, make sure that it fits to the device’s form.}

Back Cover

Attach new Back Cover adhesive tape

Back Cover Adhesive tape

Attach new 3rd Mic Hole Adhesive tape to the Back Cover

_{*The locations of ports and connectors vary by device.}

Remove all release film by grabbing the green film handle

Before proceeding, ensure that no debris or separated Screw remains inside the device

_{*Pause the video while completing each step, then resume when ready to continue.}

Attach the Back Cover and press down the edges of the Back Cover evenly in order to attach it perfectly

_{*IPXX performance cannot be guaranteed when it is repaired by user or non-skilled person.}

Insert the SIM tray back into the slots and push it in its position

Button (Volume key) 

Remove the release film of new volume button

Use your fingers to grab the volume button and insert the button on the slot carefully

_{*Press down the volume button softly and evenly so that the button can be completely assembled. Press the volume button to make sure it “clicks.” It should have the same sound and feel as before disassembly.}

Another way to prolong the life of your devices

_{*Simulated for illustrative purposes. For comprehensive technical instructions, please refer to the lastest version of the self-repair manual.}

_{*Sequence shortened. Actual steps may vary.}

Galaxy Z Fold5 Self-Repair

_{*Damage to the product caused by an attempt to repair the product by any person other than a Samsung-certified service provider may not be covered by the warranty.}

 

samsung.com

SAMSUNG