Install a stacking kit on your Samsung washer and dryer

If your laundry room needs some rearranging, you can stack your Samsung Bespoke washing machine and dryer using the Bespoke Stacking and MultiControl Combo Kit. It’ll let you securely place your dryer on top of your washing machine and provide extra space for loading and removing clothing. You can also use the standard Stacking and MultiControl Kit with your standard Samsung washing machine and dryer.
A Samsung washer and a Samsung dryer stacked onto each other in a laundry room
A Samsung washer and a Samsung dryer stacked onto each other in a laundry room

Install a stacking kit on your Samsung washer and dryer

Install the Bespoke Stacking and MultiControl Combo Kit

After purchasing your Bespoke Stacking and MultiControl Combo Kit, you can refer to our video for installation instructions. Or, use our step-by-step instructions below. Keep in mind that two people are required to lift the dryer onto the washing machine.

 

Provided stacking kit components

  • Installation guide

  • Hex-head screws (4 pieces)

  • Philips-pan head screws (10 pieces)

  • Washers (4 pieces)

  • Left side top cover bracket

  • Right side top cover bracket (with multi-connection cable attached)

  • Front cover

  • Bracket guide

  • Stacking guide

 

  1. Make sure the power cord is unplugged before starting. Tighten the leveling feet of the dryer until they are secure.
  2. Pull out the washing machine, and then unfasten the two screws that are attached to the rear of the appliance.
  3. Check the capacity of your washing machine and locate the correct assembly holes on the top cover bracket.
  4. Fasten the top cover brackets to their corresponding stacking guide.

    Note: Ensure the top cover brackets are on the correct sides (left and right) of the stacking guides before fastening them.
  5. Position the assembled stacking guides on the curved edges of the washing machine’s top cover. Fasten the stacking guides.
  6. Assemble the bracket guide to the stacking guides at the front end and then check the alignment.
  7. Remove the release liner from the double-sided tape that is attached to the bottom of the stacking guides, and then attach the stacking guides to the washing machine. Then, remove the bracket guide.
  8. Lift the dryer and place it on the stacking guide. Then, push the dryer until the two rear legs are properly locked into the stacking guides’ slot.

    Note: The front edges of the stacking guides should align with the front edges of the dryer’s side frames. Make sure the front edges are not sticking out past the stacking guides.
  9. Attach the bracket guide to the stacking guides and secure it in place.
  10. Hold the front cover with “UP” facing upward. Align the hooks on the front cover with the holes on the stacking guides. Then, fully insert the hooks to attach the front cover to the stacking guides.
  11. Open the connector port covers on the washing machine and dryer, and then connect the multi-connection cable on both ports. Close both connector port covers.
  12. Attach each wire holder to the designated slots on the washing machine and dryer.

 

 

 

Read less

Install the Stacking and MultiControl Kit

When installing the Stacking and MultiControl Kit, make sure to use a kit that is compatible with your Samsung washing machine and dryer. Two people are required to lift the dryer onto the washing machine. Additionally, do not lay the dryer down on the floor when installing the stacking kit, as doing this may scratch the dryer.

 

You can use the following steps to install your Stacking and MultiControl Kit, or refer to our video.

 
Provided stacking kit components
  • Stacking support guides (2 pieces)

  • Rear bracket

  • Screw-hex head (4 pieces)

  • Screw Phillips-pan head (8 pieces)
  • Washer (4 pieces)
  • Assembly bracket stacking

 

  1. Make sure the power cord is unplugged before starting. Place the dryer on a non-slippery floor, and then tilt the dryer on its side.
  2. Make sure the legs are facing upwards, and then tighten them securely in place.
  3. Insert the stacking support guides in the rectangular holes located in the dryer’s base until you hear a clicking sound. You do not need to remove the legs.
  4. Repeat the above steps on the other side of the dryer.
  5. Do not tighten the stacking kit screws completely. Instead, loosely fasten two rear brackets at the rear of the washing machine using the provided screws and washers.
  6. Lift and position the dryer and slide it backwards so it makes contact with the rear brackets.
  7. Align the rear brackets with the mounting holes on the rear of the dryer.
  8. Loosely assemble the rear brackets on the rear of the dryer using two screws.
  9. Tighten the screws on the dryer’s side of the rear bracket. Then, tighten the screws on the washing machine’s side of the rear bracket.
  10. Assemble the provided bracket stacking on the right side, and then assemble the rear bracket on the left side.
  11. Open the connector port cover on the washing machine and dryer, then connect the wire on both ports, and then close the cover. Do not pull on the wire.
  12. Find the holder wire that is pre-attached to the wire, and then attach the holder wire to the washing machine and dryer. Make sure the washer and dryer are connected.

 

 

 

Read less
Was this content helpful?
We're here for you

Contact Samsung Support

Contact us online through chat and get support from an expert on your computer, mobile device or tablet. Support is also available on your mobile device through the Samsung Members App.
auto-contact_us-pc-2x auto-contact_us-pc-2x